Contamination Control for Environments Where Failure Isn't an Option
Stop contaminants at the door, in the air and on the surface, with matting, nano-coating and assessments built for pharma, semiconductor and healthcare facilities.
What contamination costs you
A surface can look clean and still carry the particles, microbes or moisture that cause batch rejection, failed audits, higher bacterial counts, poor indoor air quality and food safety risk. In controlled environments, visual cleanliness is not proof of control. SGH helps you measure it, control it and prove it.
Evidence, not appearance
We combine physical barriers, surface treatments and environmental monitoring so that hygiene in your critical areas is measured and documented, not assumed.
Stop contamination at the entrance
Reusable contamination-control matting for critical entry points. It captures foot- and wheel-borne particles at the door, before they ever reach your cleanroom or production floor, and it's cleaned by mopping and squeegee drying instead of being peeled off and thrown away.
- Retains up to 99.9% of foot- and wheel-borne particles (per CC Matting information; performance depends on location, traffic and cleaning regime)
- Up to 80% of contamination enters controlled environments at floor level, mainly through foot and wheel traffic
- Expected lifespan about 4 to 5 years, fully recyclable
- 100+ successful installations
Same corridor, controlled entry
The corridor above shows the same entry point before and after CC Matting was fitted at a hygiene-sensitive site. The mat sits flush at the threshold and is maintained in place, rather than replaced sheet by sheet.
A surface treatment that keeps working between cleans
What it is: A non-toxic, alcohol-free antibacterial and antiviral surface treatment. It forms a protective layer that kills and decomposes bacteria, viruses and airborne mould spores on contact, tested and proven to last up to 6 months after a single application.
Who needs it: Hospitals, schools, hotels, offices and any high-traffic surface where you want protection between cleans, not just during them.
Assess
Assess the surface material and application environment.
Prepare
Clean and prepare the surface.
Apply
Apply the coating.
Verify
Verify the treated surface.
Maintain
Recommend a maintenance and reapplication schedule (actual service life depends on the surface, environment, cleaning frequency and chemical exposure).
What you get: Broad-spectrum antimicrobial and antiviral protection, deodorising and anti-allergen benefits, and fewer conditions for mould and fungus to spread, without repeat treatments every few weeks.
Assessment and monitoring for the air you can't see
What it is: Assessment of the environmental conditions inside your building, covering parameters such as temperature, humidity, carbon dioxide, particulate matter and other indoor air indicators, plus cleaning of the ventilation ducts that carry that air.
Who needs it: Facilities where visual cleanliness doesn't tell you what's in the air: offices, hospitals, hotels, manufacturing and any building where air-conditioning maintenance has been neglected.
Assess
Assess relevant IAQ parameters for your facility.
Identify
Identify potential IAQ issues, including duct insulation deterioration and stagnant airflow.
Clean
Clean and disinfect ventilation ducts using specialised tools.
Recommend
Recommend practical improvements.
Monitor
Set a monitoring or maintenance schedule.
What you get: Objective information on air you can't see, cleaner ducts that stop breeding bacteria and mould spores, improved airflow and HVAC efficiency, and fewer costly repairs from deferred maintenance.
Know before you clean
Visual cleanliness doesn't prove control. These assessments give you evidence instead of appearance.
Surface contamination analysis
Assesses particulate and microbiological contamination on surfaces that may look clean. Helps identify areas of concern and verify whether cleaning and contamination-control measures are working, including before-and-after testing for certain treatments.
Moisture and mould risk assessment
Identifies moisture intrusion, condensation, humidity and drying conditions that lead to mould, so you can act on risk conditions early, before a visible mould problem becomes extensive.
Ventilation and airflow evaluation
Examines how effectively air moves through a building or controlled environment, and recommends improvements where stagnant areas or uneven conditions are reducing environmental performance.
How this service is delivered
Built for controlled environments
- Pharmaceutical and biotechnology manufacturing
- Semiconductor and cleanroom facilities
- Healthcare and hospitals
- Food and beverage manufacturing
- Data centres
- Aviation and precision manufacturing
How we work
Identify
We assess your facility and map where contamination can enter or take hold.
Recommend
We propose the right combination: matting, nano-coating, IAQ assessment or site testing.
Implement
Our technicians install, apply and configure the agreed solution.
Maintain
We report on a fixed cadence (twice in year one, then annually) and adjust as conditions change.
Trusted by 300+ clients
Including Infineon, Intel, MITEC and UEM Edgenta.
ISO 9001:2015 certified quality management (NIOSH Certification, cert Q-256/25). MyHijau Mark certified (MyHS00090/26).
Compliance
Frequently asked questions
What is contamination control, and why is it important?
Can SGH assess contamination rather than simply clean it?
What is antimicrobial nano-coating, and how long does it last?
Can SGH assess indoor air quality?
Can SGH identify moisture and mould risks before mould becomes a major problem?
Does SGH only provide one-off services?
Explore more of what we do
Ready to talk to a specialist?
Get a free, no-obligation consultation
We aim to respond within one working day. Site assessments are normally arranged within five working days, subject to location, access and project requirements.
- +603 6187 6866
- WhatsApp +60 12-649 4786
- enquiry@sghygiene.com.my
- G-23A & 1-23A, Sky Awani Commercial, Jalan Sentul Pasar, Sentul, 51100 Kuala Lumpur
- Monday to Friday, 8.30am to 5.30pm